aquacraftmodels.comWARNING:• NEVER attempt to swim after a stalled RC boat! • Never operate your RC boat while standing in the water.• Never operat
10Screw the switch in place; do not overtighten the screws.Install and glue in the small rubber rod seal by slipping it over the ON/OFF wire and gluin
11On the dual servo arm only, use a 5/64" drill bit to enlarge the holes furthest out on the servo arm spokes. Do not enlarge the hole on the sin
12Slide the completed steering servo arm into the radio box from the inside. The rods protrude through the pushrod rubber seal mounts.Slip the rubber
13Install the screw lock connector onto the servo arm with the one remaining spoke. Slip it onto the servo for safe keeping. At this time it’s a good
14Although not necessary, we recommend tack gluing the radio box into the boat with a few small dabs of household cement or silicone sealer.Install th
15Using a moto-tool and cut off wheel, cut the stainless throttle cable 20-3/4" (527mm) long. It’s best to place a short length of masking tape o
16Next we are going to install the ON/OFF pushrod guide.Slip the guide over the pushrod and position it as shown in the picture. Using a 1/16" dr
17If your receiver has an external antenna you can use the include antenna to extend it from the radio box. Drill a 1/4" hole approximately 1&quo
18FINAL CHECKS AND SETUPPosition the lower unit into the slot on the set up board.Using a small machinist rule (you can get one at your local home sto
19Detach the servo arms from the top of the servos and turn the radio system on. Adjust the steering arm to center and the throttle arm to the positio
2INTRODUCTION & DESCRIPTION CHANGESThank you for purchasing the AquaCraft Top Speed 3 (TS3). We at AquaCraft want the time you spend with your boa
20Squeeze the throttle trigger on the transmitter as well as push the throttle barrel into the full throttle position. Snug the set screw on the screw
21CARE AND MAINTENANCEIf you should happen to drip or spill fuel on the fi nish of your TS3, carefully wipe it off as soon as you can. Some fuels, espe
22boat can become an instant winner just by using the right propeller. As a rule of thumb, non-lifting propellers are best-suited for your tunnel hull
23ORDERING REPLACEMENT PARTSTo order replacement parts for the AquaCraft TS3 use the order numbers in the replacement parts list that follows. Replace
AQUB0007-0010 Mnl© 2010 Hobbico®, Inc.Stock # Description Type Diameter Pitch BoreAQUB9720 40 x 52/3 3-Blade 40mm 52mm 3/16"AQUB9715 4
3SAFETY PRECAUTIONS• Never, ever, attempt to swim after a stalled RC boat. DO NOT get in the water for any reason to retrieve your boat. Your TS3 has
4BOAT STANDYou are going to want to build the boat stand as soon as you can. It makes assembling the boat easier and the stand can be used as the star
5PREPARING THE ENGINEFOR THIS STEP YOU ARE GOING TO NEED:➧ #1 Phillips screwdriver➧ 4mm nut driver➧ Thread locking compoundPrepare the engine by insta
6Slip the metal backing plate into the opening in the back of the boat. You will have to rotate it 90° to align the screw holes.Attach the engine to t
7Center the tray on the back tank platform. Using a 1/16” drill bit, pre-drill the mounting holes.Screw the tray in place using the provided 2mm wood
8RADIO BOX ASSEMBLYFOR THIS STEP YOU ARE GOING TO NEED:➧ Medium CA glue or 12 minute Epoxy➧ #1 Phillips screwdriver ➧ 1.5mm hex wrench➧ Moto tool wit
9Use a 5/64" drill bit to enlarge the hole in the switch for the ON/OFF switch pushrod.Slip the switch (ON facing to the front of the boat) throu
Kommentare zu diesen Handbüchern