ASSEMBLY AND OPERATION MANUALWARNING: 1. Never attempt to swim after a stalled R/C boat. 2. Never operate your R/C boat while standing in the wat
❏ 5. Off or stop position. If this is not the case, move thesteering servo reverse switch located on the front of thetransmitter (2) to the other posi
11STARTING THE ENGINE AND LAUNCH PROCEDUREThere are several simple steps to starting the engine. It is a good idea to have another person hold the boa
12Understanding your carburetor and learning how to adjust it:A. High-Speed Needle (HSN). The needle located on the right side of the carburetor when
BASIC MAINTENANCERemove standing water by pulling out the drain plug and draining away any water that might have entered the hull.Remove the hatch cov
14HULL TUNING TIPSAs an initial starting point, try running the Rio 51 with aneutral propeller thrust angle. This can be checked byplacing a straighte
15ADJUSTING THE TRIM PLATESYou can also use the trim plates to adjust the ride of theboat. Bending the plates down will help keep the boat from propos
1616BALANCING THE PROPELLERAlways use a balanced prop. An unbalanced prop will cause high levels of vibration that may be harmful to your driveshaft a
17• Place the buoys similar to the above sketch. Note: The above patterns are not based official standards. You may set up race courses any way you
18Order # DescriptionAQUB6207 Cowl – BlueAQUB6208 Cowl – YellowAQUB6209 Cowl – RedAQUB6323 Decal SheetAQUB6420 Cable Oiler CollarAQUB6504 Iso Engine
CYLINDER/PISTON/CRANKSHAFT PARTS LISTKey # Description Stock # 1 Spark Plug NGK CMR6A FJIG7475 2 Cylinder Set FJIG4381 3 Hex Bolt 5x18mm/S (4
THANK YOU! Thank you for purchasing the Rio 51! We at AquaCraft know how exciting a new R/C boat purchase can be and we know you’re anxious to get sta
ENGINE PARTS LISTKey # Description Stock # 1 Inlet Manifold Gasket FJIG5481 2 Carburetor Insulator Set FJIG5501 3 Hex Bolt 4x18mm/WS (2) FJ
21CARBURETOR PARTS LISTKey # Description Stock # 2 Inlet Screen FJIG5460 3 Pump Body FJIG6930 4 Set Screw FJIG7170 5 Pump Gasket FJIG7060 6
CHECK OUT THESE OTHER SENSATIONAL AQUACRAFT PRODUCTS!AquaCraft SuperVee™ 27 RTRCombining electric powered, ready-to-run simplicity with innovative Gri
23AquaCraft U-18 Miss Vegas™ Nitro RTRDesigner Jerry Dunlap is a 10-time national champion – no wonder the U-18 Miss Vegas RTR is a winner! The pre-pa
™High-Performance Metal PropsHigh-Performance Metal PropsPrecision cast fromPrecision cast fromCopper-Beryllium-TitaniumCopper-Beryllium-TitaniumThe b
WARRANTY SERVICEAquaCraft will warrant your Rio 51 for 90 days after purchase from defects in materials or workmanship of original manufacture. AquaCr
4PREPARING TO OPERATE YOUR RIO 51SPARK PLUGThe recommended spark plug is a NGK CMR6A (FJIG7475). To avoid possible engine damage, do not use any other
555FINAL ASSEMBLY & OPERATIONSome decals are installed on your boat for you. Extra decals provided in your kit allow you to customize your Rio 51.
❏ 4. Turn the transmitter “ON” using the switch on thetransmitter’s left side. The battery level indicator light (LED) should glow red. If the light i
❏ 4. Slide the receiver antenna into the top of the radiobox cover by gently pushing it in place. ❏ 5. It is only necessary to push the antenna in to
88❏ 8. Replace the radio box cover and radio box lid retainer.Use your screwdriver to install the retainer.❏ 9. Using the screwdriver, carefully pry t
CHECK THE RADIO SYSTEM❏ 1. Stand behind the boat with both the transmitterand receiver turned on. Rotate the steering wheel to theleft. The back of th
Kommentare zu diesen Handbüchern